Jump to content

Triggering UV LED on & off


Recommended Posts

Hey all,

I'm just starting out with my first flatbed, based on an Epson R2880. At this point I'm putting together a BOM so I can order everything and start building once it is all here. One of the 1st things I've ordered (foolishly or not) is a 50W UV LED module, can't remember the wavelength at this moment but  suited to what the ink supplier said it required. I also ordered a dimmable power supply.

The basic concept for triggering which I thought about is using two optical switches at each end of the travel but then I came to realize that the printer does not always travel the full distance because I might print on a smaller area. An accelerator comes to mind, however this feels like an overkill. Perhaps there's some digital signal in the printer that I can tap into and using a simple MCU (or even with just logic components) trigger on & off?

Thanks!

Link to post
Share on other sites

@ Tstern83: Really very nice UV printing system!!!!

Today i have received my Epson 1500W and i also plan to build UV light system because i want to print on objects, not on garment. Unfortunately there is not so much information available for UV light printing. Can you help me as a newbie with your experience to clarify some basic UV light questions???

1. Where to get the UV light to be used in the printer? Any shop in EU/Germany?

2. Is it necessary to place the UV light in the printer beside the printing head or would it be also possible to use normal UV light (e.g. as used for nail polish) for curing outside of the printer. Is this mandatory to cure immediately inside the printer or just to increase the productivity speed?

3. Which UV ink and UV light can you recommend for Epson 1500W printer?

4. Is there also other non UV light based ink available which could be used to print on objects? Or is UV ink the best and only solution for this task?

Many thanks in advance for your answers!!

Chris

Link to post
Share on other sites
  • 1 year later...
On 2/6/2019 at 9:08 AM, reptilesink said:

You just need some form of switch to turn it off when over the capping station.

This could be a simple proximity switch.

Is there any diagram or diy of how to do it ? i need one of those for my setup.

Link to post
Share on other sites

The light needs to be mounted to the print head so it cures as printing.

There are various types of inks such as eco solvent and latex.

For eco solvent you will need tk replace a lot of parts on the printer or it will melt the plastics.

Latex you need a heat source to cure it as it prints.

 

For the on/off of the led light when over the capping station you can just use a momentary lever switch like used for the backstop, a laser, proximity sensor etc. You just need it to be triggered by the print head as it goes over the capping station.

Link to post
Share on other sites
  • 1 month later...
22 hours ago, vanrithy said:

 

How would I wire this system to work with proximity sensor?

As a noob at this I've searched around for a while but I seem no clue about this.

Thanks in advanced!

 

1.jpg

  • Like 1
Link to post
Share on other sites
16 hours ago, reptilesink said:

You would need to find out the spec of the unit for if it needs an no or nc sensor and what voltage it operates with.

I would expect it to be using dc.

Hi Reptilesink,

This is its spec.

  • Power: 0-50W adjustable
  • Voltage: DC22-24V
  • Wavelength: 395-400NM, 365-370NM
  • Use chip: South Korea LG imported South Korea LG imported chip
  • Forward current  Forward current: 0-2000mA
  • Optical power: (395-400NM wavelength) 0-12000mW/cm, (395-400NM wavelength) 0-2500mW/cm.
  • Recommended irradiation distance: 5-10mm
  • Lamp head dimensions: 35.8 * 14.6 * 22.4 mm
  • Radiator size: 230 * 186 * 123mm
  • Packing size: 29.5 * 24 * 20.5cm
  • Suitable for small size printers, Epson R1390, L1300, L1400, L1800 and other printers modified UV flatbed printers
  • Use Epson XP600, TX800, DX5 print head

It seem to use DC. I'll check whether it needs NO or NC sensor more. Thank you!

11 hours ago, uhim said:

 

1.jpg

Hi Uhim, Thanks for your input!

I just know that much! I wanna attach proximity sensor like this:
51GQPY5KkVL._SL1001_.thumb.jpg.4d6fb560481bab463470189c0bb253c9.jpg

So, do I just need to connect like Blue + Black & Brown + Red as normal or I need additional stuff(s) to make it works?

Thank you!

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...