Jump to content

dropship88

Members
  • Posts

    10
  • Joined

  • Last visited

Everything posted by dropship88

  1. It's a very scary case, and I'm using 1 print for a part because it's completely stupid. In the case of a fake paper jam, an attempt was made to repair it by citing postings from YouTube materials and other forums, but it failed, eventually moving to the official service center, also at the official service center ---new motherboard and pe sensor were exchanged, but it worked again Serious damage to the head during one repair attempt.... Not sure if it's because of [Chipless firmware], 3 of the same [Chipless firmware: indicated by ink level pool] 2 are from another brand [Chipless firmware: ink] Volume moving display] 1 out of 3 fake paper jams. Error message while printing without any prior warning....unlucky case -.- Use an air cleaner spray with a long straw to clean with a roll. Do not try the roll because it is inconvenient to use. Even if only the pizza wheel is removed, there are some that are of good quality, but if not, the pizza wheel + star wheel holder assy (plastic: the paper inlet side, not the outlet side) is removed and used. Suction fan is not planned. I tested it a few times with a model with this symptom, and the conclusion is that the internal leveling problem and the strength of the ball fastening, etc... When the pizza wheel is removed, a minute deformation is expected in the star wheel holder assy parts... The conclusion is that when the star wheel holder assy is removed no big problem. 100% empathy. thx~
  2. Yes, the xp15000 has serious problems with rear paper feeding. 1. Fake paper jam problem - There is a problem with PaperSense. There is still no clear solution for this part. Part replacement is the best solution 2. The paper cannot be fed normally because the back of the dtf paper is too slippery. (There is no need to clean or disassemble the larger of the two rubber rollers in the rear feed paper input) 3. Paper pressing phenomenon due to the elasticity of paper. When the paper passes through the black plastic part (a.star wheel holder assy) and the rubber roller under the connected metal (b,star wheel holder assy), the paper with weak elasticity after printing from the head In the case of , a very serious line is created as the paper moves up and down and the ink comes into contact with the bottom of the a.star wheel holder assy. It is also important to check the level of the internal parts, not the horizontal-outside level of the printer. Emission related parts. Paper is best tested by retailing a wide variety of brands. The above information is based on my first-hand experience.
  3. It is being set for a black t-shirt. I tested it up to 150% density (B) I worry because there is no satisfactory result. Which of B (density) and C (Opacity Contrast) will be prioritized over white ink density I tested it Density 125 Opacity Contrast -15 VS density 150 Opacity Contrast 0 is related and there seems to be little difference. (I personally judge that there is no comparative difference) Complaints ><><><>Is the weather influence?? White cartridges Partially start curing of the print head after a day or so..... -.- -.- The (probably) biggest downside of EK is... Too little information on skills and usage... YouTube and postings, etc.
  4. It may differ depending on the ink brand, but for general DTF How to optimally set up "EK Print Studio" with xp15000 printer? Too much test paper is already consumed. Please help~ Image reference --->>>
  5. AcroRIP V10.x officially supports XP-15000. Other users are using printers that are not supported by AcroRIP V9. It is said that AcroRIP selects a printer supported by AcroRIP similar to the ink adjustment and the corresponding printer's header, and uses several details individually. For testing, download AcroRIP V9 (free version or dark version) and try it out ....
  6. Which RIP are you planning to use? Are cartridges for refilling? CISS? I am also thinking about choosing the Epson XP15000 (Epson XP15010).
  7. EKPrint Studio is possible. AcroRip 9xx version is probably also possible. (((The next expert appeared~
×
×
  • Create New...