Jump to content

All Activity

This stream auto-updates     

  1. Past hour
  2. Yesterday
  3. Last week
  4. Hello, Does UV ink harm the cleaning station? What should I do with this foam under the print head? Thank you!
  5. what leds would you recomend ???
  6. It will do it OK. Depending in the leds and the heat sink used you don't always need water cooling and just a fan for air exchange is enough.
  7. or would a motorbike radiator and a pump be better for keeping it cool
  8. will this keep the uv light cool enought i was think of this kit plus a 25 littre water drum and the batter pass from the drum thought this fan system
  9. hi everyone is there any uv ink out that suitable for clothing ????
  10. Height adjustment system will give you problems. This will work only with lower speed prints, if it works at all.
  11. Hello, do you share the 3d files of the adjustable bed frame?
  12. Earlier
  13. can i use this code for arduino mkrzero / samd21 m0? or only use to aio mkr board?
  14. Good night friends! The problem of the error was solved, I acidentally pul a wire a few days ago, and the weld of Encoder B on the SUB Board has broked, the copper rail was interrupted, so the signal for automation worked, but not for the printer, so I got the error 0xE4 or E4H, Now I'm putting all the parts together, and let's go to test it with open DTG code, because my code give this aditional step on printing, about it, what can be the motive?
  15. Are the gears that adjust the head height etc to the right if the capping station correctly aligned? If out of synch that will cause problems. When the head returns over the capping station it should lower and raise the head but if the gears are not correctly aligned with each other then they cant function. Each one will have an alignment mark on them.
  16. 0xE4 is to do with the carriage return so probably a bad connection on the flexible cable between the head and the main board or a dirty/damaged encoder strip.
  17. Good morning! Yes friend, it lights up, I tried to turn the printer on with a new encoder board and nem encoder wheel+motor, and it gives the same error, if I send the platten back and turn the encoder by hand, the platten moves correctly 😕
  18. Does the encoder light up? You have probably tried something, hopefully just on the sub board but possibly the main board if it gives the same error with a replacement encoder.
  19. Hi friends! Good night! I made a DTG/UV printer for a client, but on my tests it's getting some aditional steps, and later, my encoder A wire touched encoder B wire during work, a terrible mistake, so now I'm getting the error 0xE4 all the time, I tried with another complete encoder system, got the same error on PF, I'll share some photos about it and my code too (I made this code to work with 2 buttons and 2 limit switchs: Please, I need great help The code is in rar, 20 teeth pulley and 200 steps/rev on motor WhatsApp Video 2020-06-04 at 20.31.17 (1).mp4 WhatsApp Video 2020-06-04 at 20.31.17.mp4 Simple_Print_L1800.rar
  20. I hear some textile producers here, using it with epson 5113 printheads. They seem to replace printheads within 6 months, i don't know if this is releated to ink quality or somethingelse.
  21. Hello everyone. Ive got epson 1400 and 1430 needing help 

  22. Hi Roni, Which LED do you indicate? Thanks.
  23. esse modulo de led não presta. e projeto meu... baixa qualidade.
  24. 395nm is most universal for most available inks
  25. Hi Guys, I see this UV LED:https://www.aliexpress.com/item/4000224260797.html What nm Do I need?
  1. Load more activity
  • Create New...